#LANTERN CENTERPIECES PLUS#Should you opt for a candle-filled DIY? Or shop for an electric alternative online?īelow, you’ll find some stunning ways to use lanterns as unique wedding centerpieces, plus the best ways to arrange them. And deciding which one to pick can be quite the challenge. The new-age wedding day lantern is classy and comes in many forms. Use this guide to find the right one for your romantic wedding celebration. There are so many ways to utilize a lantern wedding centerpiece. It can be a great alternative to flowers, or it can be combined with bouquets, accent florals, or greenery for an elegant effect. The best part is that these wedding centerpieces works on multiple levels. The right lantern acts as a jaw-dropping gem to decorate your tables, while also serving as a romantic light source for any wedding decor. The perfect solution? Lantern centerpieces. Once you make one of these, you'll want to make many more.As evening descends on your wedding day, you need lighting that sparks a warm, beautiful atmosphere at your wedding reception. The tricky part in this project is to get everything straight and aligned while nailing/gluing. wood lantern after finishing with Danish oilĪlrighty! There you have the scrap wood lanterns for use as a wedding centerpiece. After another 15 minutes, wipe away the excess oil from the lantern using a rag. Leave it to dry for 15 minutes and apply a second coat. Use a piece of cloth to apply danish oil liberally all over the piece. We used WATCO danish oil for finishing the piece. Step 11: Once the piece is ready, it is time to finish it. wood lantern - ready after glue up for finishing Then clamp it tight using handi clamps (or any small clamp that you have with you) and use a brad nailer to put nails for a stronger connection. Apply glue on all the bottom edges and fix it at the centre of the base. Step 10: Now it is time to fix the frame to the base. Sand the base piece all the way from 120 grit to 220 grit until it is really smooth. Step 9: Now it's time for another round of sanding. Mark a square outline, 1.5 inches from the edge of the base. Step 8: Then mark the outline for fixing the frame on to the base. measuring the base board cutting the base piece First cut it out by length and then by width. Then cut the piece out using a circular saw and a wooden fence (any fence would be alright, though). Take a ¾ inch board and mark an 8 inch by 8 inch square piece for the base. Step 7: After the frame is ready, move on to the base of the lantern. It is a bit of a task holding the piece straight with one hand and doing the nailing. If you can get someone to help hold the piece, that would be best. Using a longer length will risk the nail coming out from the side of the frame. The nails we used were only 1 ¼ in length. It's best to use a combination of brad nails and Titebond premium glue to fix the frame together. Step 6: So After sanding, you've to do the joining/gluing. 4 vertical pieces and 8 horizontal pieces So since we are planning for an oil finish, start the sanding with a 120 grit sandpaper and then to 180 and then all the way to 220 grit. Step 5: So at this point, after all the lumber pieces are ready, it is time to do some sanding. cutting out the vertical and horizontal members It’s always best to use the first piece as reference for cutting the other pieces rather than measuring each time using a measuring tape. Step 4: So once the ¾ inch square dowels are ready, cut out 4 vertical members and 8 horizontal members using a miter saw. planing the pieces using the machine planer Actually a circular saw isn’t highly precise, so planing is usually necessary afterwards. Step 3: After the resawing run the pieces through the planer for making the sizes uniform for all the pieces. Of course, the easiest option is to just buy the right-sized wood! Tip: If you have a Table saw/Band Saw, it is better and safer to do the resawing with it. measuring the wood before re-sawing resawing the pieces using circular saw Mark the ¾ inch on the lumber and resaw the pieces using a circular saw if you need to do it too. Actually, ¾ inch square dowels are available at home-depot, we didn’t have it at hand, so we had to resaw the lumber to make it into a square dowel. Step 2: The next step is resawing the lumber to ¾ inch x ¾ inch square dowels using a circular saw You need 8 pieces of 5 inch length for the horizontal members and 4 pieces of 12 inch length for the vertical members. Step 1: To begin with take 1-1/2 inch by ¾ inch lumber and cut it down to the required length. #LANTERN CENTERPIECES HOW TO#Planer (only if you didn't get the square dowels)ĭrawing for the build wood lantern plan How to build the wedding lantern centerpiece.long (follow steps 1&2 if you don't have square dowels)
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |